How to Make a Hoverboard Complete Guide with Safety Instructions

The question which various parents and teens ask is how to make a hoverboard easily at home. However, most people ask about it because hoverboards typically can’t last long, and also their prices are very high. Also, some have a long life, and their quality is up to the mark. But most of these quality hoverboard prices are beyond our reach, most of which are over three hundred.

How to Make a Hoverboard

You can even make a better and reliable hoverboard at your home with significantly less effort and at a low price. Today we will tell you how to make a hoverboard at home with the implementation of 17 simple steps, which we are going to share with you. Besides, to implement these steps, most of the apparatus you need is at your home, we are pretty sure.

Read Also: Best Hoverboard for Kids

Some materials essential for making a hoverboard at home, if not in our house, can then purchase them from local hardware and electric stores or online stores. Moreover, the essential things are 12 volts D.C motor, cycle tire, and pieces of wood, usually at every home.

The Materials Which Are Required to Make a Hoverboard at Home Are:

  1. Two hoverboard motors of 24V ( their wattage should be around 120 )
  2. 12 volts, 7-ampere battery but better is to have 12 volts, 12-ampere battery as it functions well
  3. The piece of wood size should be by 2 2 inches.
  4. ½ inches wooden ply sheet
  5. ¼ inches rigid ply sheet
  6. Epoxy
  7. Wooden glue
  8. A small number of screws
  9. Little wheels which should be made of rubber ( diameter of 1 inch )
  10. A kid’s bicycle ( wheel size of 12 inches )

It is not required to get explicit materials to make this homemade hoverboard work. So, close specification materials also work well.

Step No 1: Take the Wheels of the Kid’s Bicycle

Start the homemade hoverboard project by removing the wheels from the kid’s bicycle. After you have done the removing task, then start clearing bolts from the axle, which does not take their part in the holding of the bearing, as we need the most usable axle for the project.

How to Make a Hoverboard

Step No 2: Now Cut the Frame

After that, make the frame by cutting the thin piece of wooden ply and the frame by cutting the wooden ply’s dense portion. Now you should have all these three wooden plays of the same size. Besides, it doesn’t matter what’s the shape of the wooden ply. The only thing necessary is the perfect length for placing your feet and the battery on it.

Read Also: Best Cheap Hoverboards

Step No 3: Make Space for the Battery

After completing the above steps, now cut one of these wooden ply in the battery’s size as you need to place your battery on it. Remember that What should cut the wooden ply in a square.

Step No 4: Create a Hole for Wheels

Now it’s time to make a hole in the center of 2 by 2-inch wood. Besides, drill the spot more in-depth than the wheel axle, so it doesn’t disturb you later. Also, cut the wood in equal length to the frame.

Step No 5: Now Fix the Wheels

After you have done the previous job, it’s time to fill both ends of the wood with epoxy. However, always use a decent amount of epoxy, and it should be from an excellent brand. Now mix it well and then insert and screw the wheels in both sides of the wood. Moreover, we recommend that you should allow the epoxy to get hard in a day or so. And until then, What should put on no weight it.

Step No 6: Assembling the Frame

Join the axle assembly and wheel on the thin chunk of wooden ply with the square slice out of it. Now cut two more pieces of 2 by 2-inch wood as advised before and attach them with the glue and screws.

Step No 7: Continue Creating the Frame

In the next section, you will create a lower part that will hold your battery. Now use these two by 2-inch wood and the best one of the thin pieces of wooden ply to build the structure. After that, join the lower frame with the middle frame. It is advised not to remove the wheels until the epoxy gets dry.

Step No 8: Now Join the Balancing Wheels

After creating bot

Step No 9: It’s Time to Join Motors

h the lower and middle frame, it’s time to attach the revolving wheel with the two by 2-inch wood. This back wheelset is to provide us with a healthy balance while riding.

The next step is to join the motor but keep in mind that the motor’s drive should be against the wheels. It’s not a challenging task, but when the engine operates, and the wheel starts revolving, the friction may free the motor from the frame. Therefore, to stop it from happening, you need to fix the engine. We recommend the tape to be used as a solution to this issue.

Step No 10: Make Motor Brackets

Now built the holding brackets for the motor. They should be of wood. Their primary role is to hold the engine and protect it from falling when your homemade hoverboard start works. Also, attach the flat wooden stick behind the brackets to use elastic on it for fixing.

Step No 11: Immediately Elevate the Brackets

The following two portions that progress backward are injected, and the motor brackets are connected to them as shown. They are associated with one bolt so that your motor inside the frame can revolve voluntarily.

Step No 12: Attach the Motors Now

The motors are then seized and bound with duct tape. I tried glue and epoxy but could not find a reliable result. Ensure the wheels on the motors’ heads are attached to the hoverboard wheels when you connect the motors.

Step No 13: Wiring

After all the steps taken before, you can now start the wiring work for your homemade hoverboard. Join the batteries and two 12V D.C motors parallel using the wires. Also, add the house switch between the motors, which allows the engine to operate separately. Do what we are saying; otherwise, you will not get the desired results.

Step No 14: Now, Put the Upper Frame on

If you have done all the steps successfully, you can put the wooden ply or the upper frame on the homemade hoverboard. Just use screws to fix the wooden ply on the top, and don’t apply any glue. It’s OK to use only screws.

Step No 15: Use Elastics

To finish the whole take, the next step is to add a few elastic bands from the motor’s bracket to the wheels’ axle. In this way, the motor gets firmly attached to the wheels. However, if you find that you don’t get the desired results, add some more bands to see the outcome.

Safety Measurements:

Now your homemade hoverboard is ready for operation. We are sure you will make a pretty lovely hoverboard at home if you follow our way fully. Moreover, we can say that riding a hoverboard, whether it is own made or company made is illegal and unsafe to ride without a helmet. Also, use the complete kid, including wrist, knee pads, and elbow pads, for perfect protection.

Final Words

We are hopeful that you find this article very useful in making the Best hoverboards at home. Enjoy the ride on your own built hoverboard, which is very cheap compared to the company made hoverboard but not less in quality. So enjoy it with your friend and in the park with your colleagues.

Leave a Comment